Park-tool SK-1 Uživatelský manuál stáhnout pdf

Park Tool Co.

5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.com

TL-1 Tire Lever Set

Tire levers are used to remove and install a

tire and tube from the wheel of a bicycle. TL-1

Tire Levers are tough enough for the shop and

small and light enough for taking on rides for

emergency repairs.

Tire and Tube Removal:

1. Deﬂate tire completely.

2. Insert one lever under bead of tire and hook

onto spoke.

3. Insert second lever 4” (8cm) from ﬁrst and

hook onto spoke.

4. Insert third lever 4” (8cm) from second and

slide along rim until bead of tire is removed

from rim.

5. Remove opposite side bead of tire by hand

and pull tire and tube from rim.

Tire and Tube Installation:

1. Inﬂate tube with just enough air to give it

shape and install in tire.

2. Position tire so the valve of the inner tube

ﬁts into the valve hole of the rim and points

straight to the center hub. A valve that is not

pointing straight at the center hub can eas-

ily be cut by the rim and cause a ﬂat tire.

3. Work bead of one side of tire completely

onto rim with hands; then work bead of sec-

ond side of tire onto rim. For extremely tight

ﬁtting tires, a tire lever can be used to pry

the tire onto the rim. Insert tire lever under

bead and pry bead onto rim, using caution

to avoid pinching inner tube.

4. Inﬂate tire to low pressure and inspect to make

sure both sides of the tire bead are fully en-

gaged on rim. If tire is properly seated, inﬂate

to pressure recommended on tire.

AWS-10 Hex Wrench Set

1.5, 2, 2.5, 3, 4, 5, and 6mm sizes are used to

install and adjust brakes, derailleurs, saddles,

seat posts, handlebars, stems, water bottle

cages, etc.

HCW-16 15mm Pedal Wrench/Chain Whip

A pedal wrench is necessary for removing and

installing pedals for replacement, service, or

packing a bike for shipment. The HCW-16 is thin

enough to ﬁt the wrench ﬂats of any pedal and

has a long, comfortable handle for leverage.

Removing Pedals:

1. Shift chain to largest chainring. This

helps protect hands and arms from sharp

chainring teeth.

2. Place HCW-16 on right pedal. Holding left

crank for leverage, turn HCW-16 counter-

clockwise until pedal is removed.

3. Place HCW-16 on left pedal. Holding right

crank for leverage, turn HCW-16 clockwise

until pedal is removed.

Installing Pedals:

1. Apply grease to threads of both pedals.

2. Thread right pedal (marked “R”) clockwise into

right crank by hand. Tighten with HCW-16.

3. Thread left pedal (marked “L”) counterclockwise

into left crank by hand. Tighten with HCW-16.

The HCW-16 is also used when removing cas-

sette cogs from the rear wheel. It ﬁrmly holds

the cassette cogs so a cassette lockring tool

can be used to remove the cassette lockring.

SD-2 #2 Phillips Screwdriver

SD-3 3mm Flat Blade Screwdriver

The shop quality SD-2 and SD-3 Screwdrivers

are used for adjusting derailleurs, brakes, and

a variety of accessories.

FR-5 Cassette Lockring Tool

A cassette lockring tool is used to remove and

install the cassette lockring and cogs on a rear

wheel. The FR-5 ﬁts Shimano

, SRAM

, Sun-

Race

, and other 12-tooth cassette lockrings.

Lockring Removal: Fit cassette lockring

tool into splines of lockring and install quick

release skewer to prevent tool from slipping.

Hold cassette sprockets with HCW-16 chain

whip and turn cassette lockring tool counter-

clockwise with adjustable wrench until lockring

is removed.

Lockring Installation: Fit cassette lockring

tool into splines of lockring and turn clockwise

with wrench until tight.

VP-1 Vulcanizing Patch Kit

Glass, thorns, nails, and other debris can

puncture a wheel’s inner tube, which holds

air inside the tire. The VP-1 Patch Kit is used to

patch small holes so the punctured tube can

be reused.

Patching Inner Tubes:

1. Remove tire and tube from wheel using TL-1

Tire Levers.

2. Re-inﬂate inner tube until double in size.

3. Inspect inner tube for leaks.

4. Lightly buff area around hole with sandpa-

per and wipe away dust. Deﬂate tube.

5. Apply a thin coat of vulcanizing ﬂuid and

spread evenly around area of hole. Allow

ﬂuid to dry.

6. Peel protective backing from patch (leave

clear ﬁlm on patch), center patch to hole,

and press ﬁrmly onto tube.

7. Place tube inside tire, install tire on wheel,

and pump to pressure recommended on tire.

SK-1 Home Mechanic Starter Set

HCW-16

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Park Tool Co

Park Tool Co.5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.comTL-1 Tire Lever SetTire levers are used to remove and install a tire an

Strany 2

CT-5 Extractor de Cadena Mini El extractor de cadena mini es utilizado para re-mover, instalar y recortar cadenas de bicicletas de montaña y carrera

Strany 3 - SK-1 Juego de Herramientas

Park Tool Co.5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.comTL-1 Llaves para Desmontar NeumáticoLas llaves para desmontar neumático

CT-5 Mini Chain ToolA chain tool is used for removing, installing, and sizing chains used on derailleur-equipped road and mountain bikes. The CT-5 C

Strany 5 - SK-1 Starter-Set

Park Tool Co.5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.comTL-1 Reifenheber-Set Reifenheber erleichtern Demontage und Monta-ge von

Strany 6

CT-5 Mini Dérive ChaineUn dérive chaine est utilise pour monter, dé-monter et ajuster les chaines que vous trouvez sur les vélos route et VTT. Le CT

Strany 7 - Mécaniciens Débutants

Park Tool Co.5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.comTL-1 Kit de Démontes PneuLes démonte pneu sont utilisé pour monter et d

Strany 8

CT-5 Mini-KettennieterFür Demontage, Montage und korrektes Ablängen von Schaltungsketten benötigt man einen Kettennie-ter. Der CT-5 bietet die Funkt

Komentáře k této Příručce

Žádné komentáře

Park-tool SK-1 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Pro jízdní kola Park-tool SK-1. Park Tool SK-1 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce